埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3090|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 9 _! q  b! S  o8 D  N& C9 x3 r
  `8 ^8 D3 R4 h( O! P* A- d0 [
Two  cutler –hammer advantage  starters are  doing the same thing:
/ ^. `; F0 ~' Y! [ After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again.
3 J- K& e2 F4 K7 hIt is a cycle.
: d  j9 K( [" \2 ?. Z( F! {' l) z4 D) g" h: x. r7 I, ~, [! Z, x
We isolate the network control and use the local start and stop only, the problem remains.
! T, e5 S- ~1 k- R, E8 qSwap one of the defective buckets with a good one, the new bucket works fine.* f4 ?8 Y7 U9 b4 \! F5 h7 Y
The problem should be inside the bucket., B# x: |- N; n; V$ I
& |) V$ t8 @, H( K2 h
When the problem happened, we observed that  the contactor has a pulling action but will not seal.' H8 @! ?2 R9 R1 K
Use a terminating screw divers to push in the contactor, it will not seal either.
# y0 M1 O% x- D% H4 L% \4 dConfirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.3 Y3 n" U: A$ O9 k1 y9 k- f

! b4 F- y; X+ ^1 f' {' w2 QThe next thing we can think of  is the coil, we took the coil out to have a close look.
# Z; ?* K3 A  D& a4 E  h3 UThey  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.
* ]$ {  k. _. H; F, d It is getting better  this time, we have 7-8 times of running before it quit working. 9 G6 X1 j- {% w3 y& p8 l$ W. X

$ Z2 e  N2 Y& f1 K+ L2 u( z7 nThe coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. # \: T" d% p* C0 i
, w' ?8 Y- z  ]7 i' j' H" m
Do you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
大型搬家
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 6 ]7 m3 O4 H5 G

5 S; \5 Y9 A0 w$ ]中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.
3 \( N, k- Z, K) g: HSince your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行
6 y5 ^! \/ q* t1 C! d4 W2 Q# `也想到这一点,不过这是新装的设备。- `  i: K3 Z9 J: ^% k0 a
检查过触点没问题。
大型搬家
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 10:37 , Processed in 0.500658 second(s), 17 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表