埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3089|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑
, q# I" ]: D1 L; L- ?
. U& a6 j9 f7 [0 R% ]Two  cutler –hammer advantage  starters are  doing the same thing:
9 w) {- w* F4 V7 h% E* a4 c After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again. + j  X5 {2 L& e* ]& G9 P3 i
It is a cycle.
1 @, @9 s3 E4 ]- `5 ?, ]( @  K. U  o# Z3 N, v
We isolate the network control and use the local start and stop only, the problem remains.; B$ Z( g# w8 ], Q
Swap one of the defective buckets with a good one, the new bucket works fine.
! V( ?) V. d( j% U# L* GThe problem should be inside the bucket.
6 f' R- Y: B9 j; F( f1 B# Y. @; B5 ]; _$ p
When the problem happened, we observed that  the contactor has a pulling action but will not seal.
* \0 L# ]& ^9 e- RUse a terminating screw divers to push in the contactor, it will not seal either.4 E3 Z, d2 L  W& F0 K! @5 L
Confirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.
1 o9 ^5 }( n- q
- g0 @' }9 ~' |( rThe next thing we can think of  is the coil, we took the coil out to have a close look.
- i) q( _& b; `( \: ^2 _They  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.( Z& ^& l' d6 g0 ]% f/ x
It is getting better  this time, we have 7-8 times of running before it quit working. 9 y: A- `8 Q% m5 q( \
+ q" E3 w, Q* |4 K3 @+ q2 |2 G
The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. 3 V# K+ W$ k7 p  s  f
9 \8 S$ E- Q  w  `: V4 @, u" z  G
Do you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 ' n1 y+ H( Q8 o: }: s
7 ^* f. A) ]: a+ v- ]) r; A
中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.
' ~" S- l. d/ J3 Z9 z( k  F' b# pSince your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行 : ~. d# q* I, U9 J6 H  ~9 `
也想到这一点,不过这是新装的设备。
! X0 V9 f, [" I( W' Q# O! p检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 10:29 , Processed in 0.483511 second(s), 15 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表