埃德蒙顿华人社区-Edmonton China

 找回密码
 注册
查看: 3088|回复: 4

[技术互助] Any input on Cutler-Hammer Starter?

[复制链接]
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 12:56 | 显示全部楼层 |阅读模式
本帖最后由 td456 于 2010-3-26 14:14 编辑 0 a! R- Y, x: E8 ?/ h; ]: }
  h2 H! R4 `" @
Two  cutler –hammer advantage  starters are  doing the same thing:$ w2 j( Q. l) m. U0 h  a+ s
After start 2-3 times, they will quit working, if you toggle the  start and stop buttons on DCS screen  , you will get another 2-3 running before they quit working again. : a3 `/ W- V  z2 s* I
It is a cycle.
+ _9 j. j2 N/ U: l6 z% l
# ~, h7 v6 X# I* t' kWe isolate the network control and use the local start and stop only, the problem remains.
, L/ ~, ]. D3 p1 M3 g% DSwap one of the defective buckets with a good one, the new bucket works fine.: b" F" V' V0 Q! A5 [, M' M7 F6 a
The problem should be inside the bucket.
0 P% h# [9 M# ?2 @! O6 f3 C# r" o8 P1 a5 z
When the problem happened, we observed that  the contactor has a pulling action but will not seal.
7 V* S) a$ n; \* S3 Q' P* r6 a  {) uUse a terminating screw divers to push in the contactor, it will not seal either.
- ]) ^+ d$ J+ A& oConfirm with TECH support this should be a problem with the control circuit board inside the advantage starter, we  bought two new control circuit boards and replaced the old ones, the problem is still the same.6 l+ ^8 M3 J' |4 u

, h, ~+ q, T( LThe next thing we can think of  is the coil, we took the coil out to have a close look.
+ ~* S" I; p# V- ~3 Y$ rThey  have a fork to pinch inside the two leads to make connection, it is not a good design at all. We soldered  the connection and tried again.3 h* K1 m9 d7 `# h- t
It is getting better  this time, we have 7-8 times of running before it quit working. ; W  M- t5 i! ^6 ~1 e- D# w( j& L8 }2 g
. N* a# w) a8 q, A: g9 y2 a% M5 U! D
The coil should be the problem, we ordered two of them. But it will take 5-6 weeks for us to get them. $ ]1 @& l* w* L) `3 ?- l1 [
- _" O; W7 [) K! O2 ]
Do you guys have any input on this issue?
鲜花(1) 鸡蛋(0)
发表于 2010-3-26 17:07 | 显示全部楼层
有时候主接触点太脏,也会造成启动器无法正常工作
鲜花(0) 鸡蛋(0)
发表于 2010-3-26 17:37 | 显示全部楼层
本帖最后由 贾电工 于 2010-3-26 18:38 编辑 * I1 Z. H) a; P% D" v

6 W; r. v. s$ F6 I6 w中国人在这里最好说中国话!说英语或想学英语请人到洋人论坛!
鲜花(7) 鸡蛋(0)
发表于 2010-3-26 17:42 | 显示全部楼层
Don't know cutler –hammer advantage  starters very well, but had been worked on AB switch gears for a little while, which has two different coils, one to pull the vacum bottles up which employs larger current, another one uses less current to hold the connection---if the second coil fails, it won't be able to seal the connection.5 H- b9 d5 U; V' Y0 h2 E
Since your cutler -hammer works couple times,  I guess 侠客行 is right, or the sealing connection is just worn out.
大型搬家
鲜花(0) 鸡蛋(0)
 楼主| 发表于 2010-3-26 17:55 | 显示全部楼层
2# 侠客行
) m' S! C, D7 q" Y% O7 x) P也想到这一点,不过这是新装的设备。, w# R( t1 w3 k/ |& @" V9 W
检查过触点没问题。
您需要登录后才可以回帖 登录 | 注册

本版积分规则

联系我们|小黑屋|手机版|Archiver|埃德蒙顿中文网

GMT-7, 2026-11-18 10:24 , Processed in 1.673824 second(s), 16 queries , Gzip On, APC On.

Powered by Discuz! X3.4

Copyright © 2001-2021, Tencent Cloud.

快速回复 返回顶部 返回列表